Recent Activity

Activity stream for all registered members at The Floor Pro Community.

  1. Mike Antonetti replied to the thread Hardwood or engineered hardwood flooring suggestions.

    I like hickory. You have to hold your end of the responsibility in maintaining proper humidity levels. We were installing very nice...

    Jan 24, 2020 at 5:20 PM
  2. Incognito attached a file to the thread What did you do at work today (2020)?.

    They wanted walk off mats (Tarkett Abrasive Action) at the entry to the mult- purpose room in a Junior High. 4 entry doors 6'7" x 8'9"...

    IMG_5657.JPG IMG_5659.JPG IMG_5660.JPG IMG_5661.JPG IMG_5662.JPG IMG_5663.JPG IMG_5664.JPG IMG_5665.JPG IMG_5666.JPG IMG_5667.JPG IMG_5668.JPG IMG_5669.JPG Jan 24, 2020 at 5:19 PM
  3. Kevlax2 replied to the thread Ripping and Replacing Kitchen Porcelain Tile.

    The neighboring floor is laminate that is going to be replaced with the same hickory wood floor shown on the last photo (after I do the...

    Jan 24, 2020 at 5:14 PM
  4. Mike Antonetti attached a file to the thread Fabrica Cotton Club Issues.

    Here’s the job with the cat, lady didn’t seem too upset, I’d be ringing necks

    3F35EA1B-B102-41B7-9F79-85D07654CC39.jpeg 4A1FE255-D24D-44A1-9D20-3CAEBD48C394.jpeg Jan 24, 2020 at 5:13 PM
  5. Mike Antonetti replied to the thread Ceramic tile on concrete that is lower than adjacent tile floor.

    What about condo docs stating a noise suppression must be used under tile? For ramp purposes we use to notch a 1x4 about 4 ft long....

    Jan 24, 2020 at 5:08 PM
  6. Incognito replied to the thread Cubicle Lift System.

    **************************** I agree with you. Whosoever builds these montrous systems should have a simple solution for lifting the...

    Jan 24, 2020 at 5:08 PM
  7. Incognito replied to the thread Cubicle Lift System.

    ****************************** We nearly always had to do some custom fabrication. At the same time there have always been lift tools...

    Jan 24, 2020 at 4:37 PM
  8. Mike Antonetti attached a file to the thread replacement rubber blades.

    If you analyze the question, the answer is in the material used. Now why would the supplier of that want to change anything as they’re...

    61104A7A-D1F4-4C2B-9E04-105218165C52.jpeg Jan 24, 2020 at 4:09 PM
  9. epoxyman replied to the thread Ceramic tile on concrete that is lower than adjacent tile floor.

    I would just float up to the higher tile Bring it out about 3-5 feet that way you don’t really see or feel it

    Jan 24, 2020 at 3:05 PM
  10. epoxyman posted a new thread.

    replacement rubber blades

    The vacuum heads we use have rubber blades that set inside them to get good bite to the floor we do tons of quarts floor and when we...

    2A9F07F4-3572-4A4C-AAB0-099E7AE86E0C.jpeg 78AACBAC-095D-461A-AB1F-7EEC9ECBEC19.jpeg

    Forum: Tools, Equipment and Supplies

    Jan 24, 2020 at 2:01 PM
  11. Mike Antonetti replied to the thread Ripping and Replacing Kitchen Porcelain Tile.

    You need to protect that hardwood nearby. Dropping a tile edge will indent the wood 1/4” deep. Maybe ramboard and some plywood.

    Jan 24, 2020 at 1:23 PM
  12. Mike Antonetti replied to the thread Grinder repair.

    Good to know, I like that commercial/Industrial area. I suppose if the bearings are not made in USA it’s ok. I think China may be...

    Jan 24, 2020 at 1:19 PM
  13. Jim McClain replied to the thread Bruce Fulton and herringbone layout questions.

    If you buy ready made spline, or make your own, the splines and grooves you cut should match the boards' existing tongue & groove. Most...

    Jan 24, 2020 at 10:58 AM
  14. Jon Scanlan replied to the thread Australia Bush Fires.

    I just Googled it and found this 'Fallen heroes': Bodies of US firefighters killed in NSW plane crash retrieved

    Jan 24, 2020 at 10:28 AM
  15. epoxyman replied to the thread Ripping and Replacing Kitchen Porcelain Tile.

    Yea just a small demo hammer and get some knee pads and some good gloves that tile will cut you fast been there a few times

    Jan 24, 2020 at 10:20 AM
Loading...
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.