Mike Antonetti's Recent Activity

  1. Mike Antonetti attached a file to the thread Work trailer guys.

    Exterior screws,Trim etc. can be gotten on Ebay when your trailer ages and needs fixin. This site is scary good, I think stuff shipped...

    ED26811A-111F-48F1-B27B-8467B8E83B0D.jpeg 0AF3330D-3D71-49C3-8E29-8CB2334CAAAB.png 88060C0F-D499-4441-B021-207548827347.png E4BD6439-C9C9-4582-AD08-B8910CF54082.jpeg Jan 23, 2018 at 5:07 PM
  2. Mike Antonetti replied to the thread Best Flooring For concrete Slabs with cross seam.

    So if you know anything about tile bonded directly to a slab over “control joints” then your aware tile can crack directly above those...

    Jan 23, 2018 at 4:31 PM
  3. Mike Antonetti replied to the thread Herringbone fitting.

    What country? Retail contracted or Handyman?

    Jan 23, 2018 at 3:51 PM
  4. Mike Antonetti replied to the thread VCT Tile.

    Without knowing zero about your situation a pro familiar with mixing products may opt to use R701A by Stauf. STAUF USA Adhesive to...

    Jan 23, 2018 at 9:57 AM
  5. Mike Antonetti replied to the thread New toys....

    I’m looking them up now, 3phase is a bit limiting where it can be used, usually just industrial and limited commercial buildings in our...

    Jan 23, 2018 at 8:46 AM
  6. Mike Antonetti replied to the thread Best Flooring For concrete Slabs with cross seam.

    Why 4 slabs? Sounds like a DIY, I’d be concerned about tiling but it may be able to be done. A wide picture and detail of the joint...

    Jan 23, 2018 at 8:18 AM
  7. Mike Antonetti replied to the thread Looking for a gundlach lino dolly. The one with the built in rollers..

    There’s 36’s in Oklahoma Barry for 100 each, I had to check your profile page I thought you were around there if you wanted the bigger...

    Jan 22, 2018 at 5:16 PM
  8. Mike Antonetti replied to the thread Looking for a gundlach lino dolly. The one with the built in rollers..

    That was the one I was going to keep private. 15+ hrs away to Seattle,3+ to LA if he didn’t want it and Incognito did. Tricky as...

    Jan 22, 2018 at 5:07 PM
  9. Mike Antonetti replied to the thread Looking for a gundlach lino dolly. The one with the built in rollers..

    I used one at the training school about 25 years ago that had 6' medium tech that Armstrong donated to the tech college. It worked well,...

    Jan 22, 2018 at 3:59 PM
  10. Mike Antonetti replied to the thread Hardwood Issue.

    From China, I’m growling, rrrr! Jim we cool?

    Jan 22, 2018 at 11:18 AM
  11. Mike Antonetti attached a file to the thread Looking for a gundlach lino dolly. The one with the built in rollers..

    So, this one? Truck, lingo is always confusing on the MHE Gundlach No. 4 Linoleum Truck

    8400A369-D6EB-4009-BC05-EBBFE4D52DA3.png Jan 22, 2018 at 11:09 AM
  12. Mike Antonetti replied to the thread VCT Tile.

    No, the two products should not be used together. Without a vapor barrier under slab your flooring is susceptible to failure due to...

    Jan 22, 2018 at 3:35 AM
  13. Mike Antonetti replied to the thread Looking for a gundlach lino dolly. The one with the built in rollers..

    18” or 36” and quantity?

    Jan 22, 2018 at 3:33 AM
  14. Mike Antonetti replied to the thread New house - carpet choice.

    Think I was reading Floor Trends little while ago and Shaw owns them, something about putting Anderson/Tuftex products together for a...

    Jan 21, 2018 at 2:29 PM
  15. Mike Antonetti replied to the thread Tiling Balcony Over Certainteed Flintlastic.

    What was it designed for by the structural engineer and architect? I’d not want to bond anything to it that would damage the roofing...

    Jan 21, 2018 at 2:23 PM